3 More Images

Since these are pretty acidic beans, I’ve ground them relatively fine (1.6.0 on 1zpresso Q Air), which is a wee bit coarser than what I grind for moka pot (1.4-1.5). I use Hoffmann’s “better 1 cup V60 recipe”.

It tastes fine, I think, I still don’t have a good reference point for V60. Its just that it takes a good 3-4 minutes after the last pour for final drawdown to be complete.

Sorry for the external link, i wanted to include multiple images.

  • Chais@sh.itjust.works
    link
    fedilink
    arrow-up
    1
    ·
    38 minutes ago

    3-4 minutes after adding the last drop seems very long. I imagine your code comes of quite bitter.
    Personally, I try not to exceed 4 minutes contact time. I grind with a 505μm gap between flat burrs. Result:

    Bed after 4 minutes:

  • godot@lemmy.world
    link
    fedilink
    arrow-up
    3
    ·
    13 hours ago

    The bed looks a little muddy and the brew time is long, you did stall. I would recommend using this as a benchmark and going a bit coarser.

    This is not bad, you’re likely close to technically “correct”. It can be a fine line between stalling and, if you like it, thorough extraction.

    If you grind coarser you’re going to get a more expressive cup. If you find the resulting cup is a bit thin you do have options.

    This is with the Hoffman technique omitting the final swirl. 15.0g coffee, 246g water. 40 second bloom, 3:12 total. I skipped the second swirl because I could see it was running a hair slow. This bed is a tiny bit muddy, but taste is very good. I might go one click coarser, but no more. I think one or two clicks finer and the added swirl and I’d be looking at the exact bed you had.

    I wish I’d added more light to the picture. Sorry.

    It is acidic, but it’s a high altitude Colombian coffee. It’s a pleasant green apple acidity, I paid extra for that acidity.

  • BurntWits@sh.itjust.worksM
    link
    fedilink
    arrow-up
    10
    ·
    19 hours ago

    That’s pretty long. If it’s taking 3-4 minutes after the last pour with that amount of grounds, you’re probably going way too fine. For a single cup serving, the time from your first pour of your bloom to the last drop dripping into the cup should be around the 3 minute mark. The final drawdown should only be around 1-1.5 minutes. Your bed looks well settled though. If you like the taste of finer grounds but want a quicker drawdown, don’t swirl and let the bed sort of crater. It won’t look as nice, and goes against what Hoffmann talks about, but a perfectly flat bed will slow the drawdown significantly.

    There’s other options too, the filter paper material will also affect drawdown quite a bit, as will pouring technique (how much you disrupt the grounds) but I’d start with a coarser grind and see what you think.

    • yogurtwrong@lemmy.worldOP
      link
      fedilink
      arrow-up
      4
      ·
      18 hours ago

      Thank you. I’ll try a coarser grind and if I don’t like how it turns out, I’ll try putting the last pour mostly in the middle and not swirling.

  • flamingo_pinyata@sopuli.xyz
    link
    fedilink
    arrow-up
    4
    ·
    20 hours ago

    Your grinder might produce too many fines. This is what floats to the top and gives the dough-like appearance.
    The coffee itself will still be tasty, but speaking from experience, there is a noticable difference when the grind is more uniform.

    • yogurtwrong@lemmy.worldOP
      link
      fedilink
      arrow-up
      1
      ·
      18 hours ago

      I also thought about that. I got a cheap(er) grinder but it’s burrs are pretty high quality afaik.

      I do clean it once in a while and it does spin very uniformly, so I think the fines are due to the brittleness of the beans I am using.

      A flat burr might change that, but I aint buying a new grinder lol.

    • yogurtwrong@lemmy.worldOP
      link
      fedilink
      arrow-up
      5
      ·
      23 hours ago

      Yeah but as I said, I don’t have a good reference point for V60. I was just asking if long drawdowns with single droplets resulting in this dough like bed is typical.

      • tofubl@discuss.tchncs.de
        link
        fedilink
        arrow-up
        1
        ·
        16 hours ago

        I have found that drawdown this slow leads to overextraction, and my grind is much more coarse than yours, by a factor of 4 or so. I usually set my grind size from drawdown: I look for the point where the 90g water I add to 30g coffee at a time almost completely draws down in 45 seconds.

  • owlriver@feddit.org
    link
    fedilink
    arrow-up
    5
    ·
    22 hours ago

    I am no expert, but after seeing a Lance video I started doing courser grinds. Then I do not get a smooth bed like this and the fines seem to be more in my filter.

  • Hamartiogonic@sopuli.xyz
    link
    fedilink
    English
    arrow-up
    2
    ·
    22 hours ago

    I can see plenty of fines on the surface, but that isn’t necessarily a problem. Did the liquid permeate through the bed fast enough?

    • yogurtwrong@lemmy.worldOP
      link
      fedilink
      arrow-up
      3
      ·
      18 hours ago

      I heat water in a large spout electric kettle we already had and pouring with this gooseneck cup I found.

      Best solution if you already got a way to heat water imo

      1000002405

      • jaygray91@piefed.zip
        link
        fedilink
        English
        arrow-up
        2
        ·
        16 hours ago

        Why did I never thought of this. I mean the nice goose neck kettle I have now have temperature control which is good, and have other coffee nerd niceties, but when I was thinking of buying it I definitely was sweating because it’s quite a big spend that could have gone to more beans.

      • lime!@feddit.nu
        link
        fedilink
        arrow-up
        2
        ·
        17 hours ago

        i’ve been thinking of getting one of those but the pre-heating requirement is a turn-off.

        • godot@lemmy.world
          link
          fedilink
          arrow-up
          1
          ·
          12 hours ago

          It might not be particularly onerous. It’s often beneficial not to brew at a full 100C. Between inverting the gooseneck over a standard tea kettle to catch steam to preheat the gooseneck and letting the mass of the gooseneck bring the water temp down to slightly lower than boiling I suspect it could be very effective for premium light roast coffees.

          I haven’t tried it, though, I bought an electric gooseneck before I’d realized that sort of thing could be done.

          • lime!@feddit.nu
            link
            fedilink
            arrow-up
            1
            ·
            11 hours ago

            good point! seems a bit vague though. not that it’s a very exact science anyway i guess.